PIXMA G620 - printer issues with color
Why does my photo glossy look like this on the g620 and how to I fix it? It was printing just fine so I don’t know what changed
Posts
PIXMA TR4722 Printing stopped midway through document
Good evening I have been printing and was in the middle of a printing another document when it stopped about 20pages in. I just bought and replaced the ink, no errors have appeared, I need to print these papers. I hope someone can help ASAP thank ...
PIXMA G5020 Poor Print Quality
I hadn't used my printer in many months, and just tried to print some photos & the quality is awful. They are grainy and faded, where they used to be bright & high quality. The only thing that changed was time. I went through every maintenance/cleani...
I purchased a PIXMA TS3522 and its never worked!
Its a pixma TS3522 and its a peice of junk. I have had it for 4 months and its worked once. It came with one page of instructions that were of no help. I will never purchase a cannon printer again! I hate this printer!!!
TS3722 - EO3 Error
This the 2nd printer already this year if i cant figure this out I'm going to stop using cannon products. my pixma canon TS3722 printer works great until i have to get new ink then it keeps flashing E03 and nothing i do works, I've read all user manu...
PIXMA MG3620 Alarm Light Staying lit
I just got my MG3620 and I'm trying to set it up, however when I go to connect the printer to my router my alarm light kicks on and stays on. I've tried to factory reset it and still nothing, it will print a network configuration page but not connect...
Pixma MG3600 Can't Toggle Auto On/Off under MacOS Sequoia
Recently updated a MacBook Pro to Sequoia, and Canon doesn't seem to be supporting the IJ Utility under Sequoia. Did I miss something?Every morning before I can use the printer I have to turn it on, as it keeps shutting itself off overnight.I can che...
Unable to align PIXMA MX922
Hello. Im unable to align my canon pixma, it gives me blur caracter on 3/4 lines. Encoder seems fine, I have done several cleaning, automatic and manual, let it soak for a while etc. changed every cartrige. any other advise? Im trying to check if I c...
PIXMA TS3722 - Can’t Push down the ink cartridge lock lever
I just bought PIXMA YS3722 and in the process to installation. I am trying to install the ink cartridge. But i can't puch down the ink cartridge lock lever and it is tight. What should i do?
PIXMA TS3722 - Error when installing new ink cartridges
I have a Canon TS3722 printer and even thought I an using Canon Fine ink cartridges I cannot get them in the printer. I have taken them out and reinstalled but still get an error message, they are installed correctly but error says no what else can I...
PIXMA TS9520a - Rejects 12x12 Matte Photo Paper
Hello everyone, I’m reaching out to the community for some advice on an issue I’m facing with my Canon TS9520a printer. I've been trying to print on 12x12 inch matte photo paper, but my printer consistently rejects this paper type, stating that I can...
Resolved! PIXMA MG6120 "ink absorber is almost full."
I keep getting that "ink absorber is almost full" message. I contacted customer support and was redirected to a third party tech support who said I am getting that message because my network is congested and that they could fix it for $249 and that I...
PIXMA TR8620 won't print from cassette
My printer keeps trying to print from the rear slot. Also, when printing from the rear slot it only prints 4x6. I have changed the feed settings on the printer, it says it changed to letter, but when I print it still says I need 4x6. I even tried r...
PIXMA MX922 - Code 1403
Hi everyone, I have installed new ink cartridges in my MX922 printer and I am receiving a notice: "Support Code 1403" and "The type of print head is incorrect. Install the correct print head." I've had this printer for over 6 years and have replaced ...
PIXMA MG7520 Printing blank pages, Error 1403
I paperweighted my MG7520 too with the same error code. Unlike you, I did not experience printing issues before the 1403 error code. I just got tired of seeing the update message on the display so I finally gave in and installed the firmware updat...
