Professional Photo Printers
Showing results for 
Show  only  | Search instead for 
Did you mean: 


Resolved! imagePROGRAF PRO-300 Print Head issues

Been trying to find a contact email for tech support. That page returns an error, so I'll post my issue here. I use Red River Papers, and their 60/lb Polar Matte has an issue of the print head scraping the paper in the first inch of the print. I also...

DTPhoto by Apprentice
  • 1 replies

Paper not feeding Cannon 100 series

We are having issues with printing both rear and manual tray on printer. The computer says there is no paper to feed. I tried cleaning rollers and the paper feeds fine but will not print. Need assistance. Planning to call cannon tomorrow. thanks 

Benzdc by Apprentice
  • 1 replies

Resolved! Canon Pro-100 missing colors

I haven't used this printer for awhile since I recently purchased a Canon TR8622.  However, when I tried to compare prints from both devices I discovered that the Pro-100 had gone completely out of whack as you can see from the nozzle check printout ...

donmeier_0-1671485494340.png donmeier_1-1671486197076.png
donmeier by Contributor
  • 2 replies

Prograf 1000 printing issues with Mac OS 13

Today was the first time I tried to print (from Lightroom and also from Photoshop) after updating my OS to OS13 and I noticed that the print dialogue boxes were much more elementary than before.  I.e. the options and settings seem more simplified.   ...

imagePROGRAF TA-20 Cut margins

Hello all, I recently purchased my TA 20 and have set it up and done a few prints on some different media. No problems setting up the media themselves, but am curious how to set cut margins on rolls. When printing a poster on roll media, the printer ...

Pinhole by Apprentice
  • 0 replies

Pixma Pro 10 -- Blue printing as purple

After having a previous issue a while back of my images printing with a strong magenta cast, I found out the chroma optimizer had a tiny amount of cyan on the sponge. Needless to say, I ended up replacing all of the ink with new genuine canon cartrid...

IMG_4511.jpg IMG_4512.jpg

Pro-100 and Support Code: 6910

When my PRO-100 powers up I hear motors turning and then the white and yellow lights on on the front start flashing alternately (the yellow light flashes 26 times, pauses and repeats) and I get an error code pop-up on my PC with "Support Code: 6910"....

Getting started

New to the community? Here's some information to help you get acquainted:

01/18/2023: New firmware version 1.1.1 is available for EOS R6 Mark II
01/09/2023: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
01/03/2023: Welcome to CES 2023!
12/08/2022: New firmware version is available for EOS C70
12/07/2022: New firmware version 1.7.0 is available for EOS R5
12/07/2022: New firmware version 1.7.0 is available for EOS R6
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/14/2022: New firmware version 1.0.1 is available for CR-X300
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version is available for EOS-C500 Mark II
05/26/2022: New firmware version is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version is available for EOS R5 C
03/23/2022: New firmware version is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.