Printer Software & Networking
cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Posts

Communication Error 306

Hello, I've just recently started having an issue with my printer. I used it last week and it was fine but I've been trying to get it to print for two days and cannot figure out whats wrong. I have a Pixma MG6600, connected via wifi to a Macbook Pro ...

Canon Pixma 100s Useless ?? (or is it me)

Hi Everyone, I am new to this group and just joined because of a really frustrating issue. When I switch on the printer and try to use it wirelessly it just wont connect to anything ? Ive managed to press the WPS button which flashes and I then press...

lerobe by Apprentice
  • 2464 Views
  • 5 replies
  • 0 likes

Canon MG5320

I recently changed internet providers and having trouble connecting the printer to WiFi.  It's telling me to press and hold the WPS button on the access point for about 5 seconds.  Question?  Where is the WPS button?  I'm assuming the access point is...

Canon Pixma communication/offline problem

I have a Canon Pixma iX6500 connected to a modem with via USB cable. The modem has a printing service.  The printer works with computers on the network ok when I try to print first time but if you let the printer idle for a while or turn it off and o...

connecting via a new router

Have had mg 2900 for awhile, just changed my provider, so, I have anew router. Nightmare to get the printer to work.It will print from emails etc., scan , but will not print directly from my computer. It recognises the printer etc.,I have emailed the...

philo by Apprentice
  • 2136 Views
  • 1 replies
  • 0 likes

MG5770 Cannot see my wireless router

Trying to connect my MG5770 via wireless thru a Netgear Nighthawk X4S AC2600 Model R7800 router. The printer does not see the wireless router! I have both 2.4G and 5G networls but it will not detect my router. It sees my neighbours routers!! and I ha...

Wireless network doesn't recognize PIXMA 990

I am ready to rip my hair out. I have never been able to get my household wireless system to recognize the printer. It is located right under the router, and finds the router and verifies the password during set up. But none of the computers in the h...

NanBR by Contributor
  • 6021 Views
  • 13 replies
  • 0 likes
Getting started

New to the community? Here's some information to help you get acquainted:

Announcements
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available forRF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!