Resolved! PIXMA MG7520 - Screen is Frozen
Opened the scanner menu and hit the drive icon by mistake, now the scanner screen is frozen and I can no longer scan.
Opened the scanner menu and hit the drive icon by mistake, now the scanner screen is frozen and I can no longer scan.
I have a Pixma MG8120 color printer. Due to its age, Canon tech support no longer supports it. Their chat line suggested I try this community forum site. The color of my photos were way off. I performed a color test and saw the black and cyan bars di...
I replaced the print head with a new print head. I still get the error message please install the correct print head. As this printer is retired from any Canon support responses, I am turning to the group for advice as to the nest step to get the pri...
A magnet dropped into the rear paper feeder. We got it out but had to disassemble the paper feeder. How does the spring attach? Is there a parts diagram or photo to show it somewhere? Thank you in advance!
I looked through the manual trying to figure out how to check for updates for the IJ Utility and my G7000 printer. After a lot of searching all I found was how to check or get firmware updates IF my G7000 is connected to the internet via a LAN or Wi-...
I have a new Windows 11 system (not an upgrade) and it won't accept the drivers. It wants only 64-bit drivers.I saw a post for about the mx 340 in this section and tried those. They would at least try to load but couldn't detect the printer.I would a...
Successfully installed the Windows 8.1 (x64) driver for the MX860 in Windows 11.Works perfectly directly connected and via Ethernet LAN.I'd wager the same approach will work for Win 10/11 and other Canon support retired PIXMA MX series printers.The M...
Hi, I've been going around and around in circles with my printer all morning. It had disconnected from my wifi - so I reconnect, it says Connected and then it goes right to Setup Fax mode. I don't want to set up the fax, I have no interest in the fax...
Bought a new G7020 printer and really like it for straight printing but can't get any of the other functions working. I am running windows 11 with all the updates, I downloaded all 6 or 7 software updates for all the functions for the printer.I conne...
I had to install the printer on a new device. It printed the test document just fine. But now it has a 1403 error and won't recognize one of the printer cartridges. it is a Canon MX922 printer. I tried removing and replacing the cartridge. Even went ...
Hello. We purchased a Pixma 4722 last September. It worked okay for a while, but about Christmastime it started doublestriking and misaligning horizontally, plus the next sheet of paper would be started and would jam.. I tried to get help but with...
My TR4650 is stuck on copy mode. I unplugged it pressed on button and plugged it again - didn't work. Wifi is working.
When printing with the PIXMA 9521c there is a darker and very light tint that I can't get rid of. I've tried eveything and nothing works.
I was trying to install my cannon computer. Setup instructions told me to go to scam site link removed I did and went to install the software, i was unable to do so and I got a popup message telling me not to try again but to call scam info removed ...
Subject | Author | Posted |
---|---|---|
12-25-2024 10:35 AM | ||
12-25-2024 10:11 AM | ||
12-24-2024 12:23 AM | ||
12-23-2024 03:53 PM | ||
12-19-2024 06:38 PM |
New to the community? Here's some information to help you get acquainted:
12/18/2024: New firmware updates are available.
EOS C300 Mark III - Version 1..0.9.1
EOS C500 Mark II - Version 1.1.3.1
12/05/2024: New firmware updates are available.
EOS R5 Mark II - Version 1.0.2
09/26/2024: New firmware updates are available.
EOS R6 Mark II - Version 1.5.0
Canon U.S.A Inc. All Rights Reserved. Reproduction in whole or part without permission is prohibited.