I have Canon MX860 printer. When I now go to print, I hearing a clicking noise.
It sounds as if a gear is being stripped and now the printer will not print. It has been a great printer until lately. Any suggestions appreciated.
It sounds as if a gear is being stripped and now the printer will not print. It has been a great printer until lately. Any suggestions appreciated.
My MX892 prints for 20 secs. then stops for 20 secs. prints for 20 secs. stops for 20 secs.This is repeded until the job is compleeted. I am running Windowes 7 .I have updated both windows 7 and the printer drivers.
Sorry for the double post - I notice my original post was in the wrong forum. I have some paper jammed in the automatic document feeder on my MF4890dw. I followed the steps in the support dicument (http://kbsupport.cusa.canon.com/system/selfservice....
Hello everyone, I´m using a Canon iR C4580 and I have no problems printing but the scan isn´t working it always gives this error:"Canon WIA Network ScanGear DriverA system error has occurred. Check the scanner or computer status". The scanner is alre...
Canon mg 3100 not scanningErrorCannot scan for these reasons :-(if using LAN connection) it is disconnected from LAN-(if using wireless LAN connection) signal strength is poor due to obstruction-network connection is prohibited by security software-d...
Hi, I have a Canon MG3250 all in one that is 2 weeks old. Yesterday I updated my desk top operating system to Windows 7 from XP and now I can't get the printer to print. The scanner works fine. I've tried uninstalling and reinstalling the drivers, do...
I purchased the new Canon Pixma MG7120 yesterday. All descriptions of this printer state that is can print on CDs and DVDs and that indeed a tray comes with the printer. Much to my dismay when I opened the box there was no G tray in it. Does any one ...
Hi: I have a Cannon Pixma 3100 series printer which seems to be printing in a double vision. The lines and words are all where they should be. I've done the head alignment, nozzel check and all that stuff but it won't fix it. Please help.
I can't connect to my MG5220 wirelessly now that I'm using Windows 8
Hi,I bought my printer a couple of months ago and it worked fine. Until a few days ago it just broke down with a code error 5011...I came home turned it on and 'beep beep beep'. I am unsure what happened. I know I was running low on ink so I bought i...
HiI'm a student in a big shared flat. Because we are using the same wifi everyone can print on my Canon MG7150. Is it possible to see who had printed or better can I change the settings that only I can print (maybe MAC or IP...?). Thanks in advanced...
The Unit will NOT power on. Only the Yellow ALARM LIGHT stays on. Tried unplugging etc!
Subject | Author | Posted |
---|---|---|
04-01-2025 12:31 AM | ||
04-01-2025 12:18 AM | ||
03-31-2025 11:06 PM | ||
03-31-2025 07:22 PM | ||
03-31-2025 02:42 PM |
New to the community? Here's some information to help you get acquainted:
03/18/2025: New firmware updates are available.
EOS R5 Mark II - Version 1.0.3
02/20/2025: New firmware updates are available.
RF70-200mm F2.8 L IS USM Z - Version 1.0.6
RF24-105mm F2.8 L IS USM Z - Version 1.0.9
RF100-300mm F2.8 L IS USM - Version 1.0.8
RF50mm F1.4 L VCM - Version 1.0.2
RF24mm F1.4 L VCM - Version 1.0.3
01/27/2025: New firmware updates are available.
12/18/2024: New firmware updates are available.
EOS C300 Mark III - Version 1..0.9.1
EOS C500 Mark II - Version 1.1.3.1
09/26/2024: New firmware updates are available.
Canon U.S.A Inc. All Rights Reserved. Reproduction in whole or part without permission is prohibited.