Printing Labels with PIXMA G4210
I have tried unsuccessfully to print address labels using Avery 8 1/2 x 11 label sheets but the printer jams. Is there a setting I need to select to print the labels?
I have tried unsuccessfully to print address labels using Avery 8 1/2 x 11 label sheets but the printer jams. Is there a setting I need to select to print the labels?
I have a Canon MG8100 printer & scanner. It still prints fine - but has stopped scanning, or even seeing the scanner in the Solution Menu. I've reinstalled the driver as MP Navigator 4 suggest - but made no difference. I'm working from a Mac Book Pro...
What if you upgrade your laptop and there is no cd-rom? In order to use printer one needs to have original software. I am having trouble finding the original software from the cd that came with my mp280 online. The only software I am finding are upda...
I just finished setting up My TR7520. after the setup was complete i tried to test print something and it just comes out blank. i am not getting any error codes, nor did i while doing the initial set up . please help
I have this orange piece from inside my printer, where does it go and how do I put where it goes
My MX532 ADF (automatic document feeder) will no longer work. I've used it a lot with no issue, but it stopped pulling in the paper. I've looked online for troubleshooting, but am not finding anything.
Hello, I recently got a new Xfinity modem and am being prompted on my Pixma screen to enter passphrase. Never had one before, so where do I start? Thanks!
Hello! I have been seaching :"high and low" trying to find how to locate the ink level on my printer. I need to get to the place where I can also get the ink level information to come up on the screen when it is low. I just can't find this informatio...
My 2522 prints from the last page toward the front page lots of wasted paper. Can this be changed ? thanks
I am using windows 10 on a dell desktop and when i try to print I get an error it can't print the document and shows the error status in the queue but it will print anyway. This is not a serious issue but can it be corrected?
This light has always gone out within a few minutes. I have two of these printers and they both have this problem. I just updated the firmware, maybe that's it. How can I turn these lights off?Thanks
My mx492 I just bought yesterday has error message-Install he cartrigges properly. I reinstelled them twice. No gelp. Get same response.
Is there a good way to print on thick, stiff paper? Curling the front edge seems to help. I am trying to print on green full 8 1/2 x 11 labels, they are thicker and stiffer than normal white labels like #8165 Avery labels, but I wanted the colored ba...
Hello, i have a faulty part on my cannon and i dont know how this piece is called or even where to buy it.My error is that one pin is broken and the cartridge isnt recognised.Its this black parthttps://www.dropbox.com/s/nq6j5my227qztzj/IMG_20190224_1...
Greetings to the Board - this is my 1st post here. A couple of years ago I bought one of these printers for a couple of reasons: it feeds paper "straight" from a rear "standing" supply, so I can more easily feed card stock. And it was recommended by ...
Subject | Author | Posted |
---|---|---|
02-10-2025 01:26 AM | ||
02-09-2025 11:32 PM | ||
02-09-2025 09:59 PM | ||
02-09-2025 03:48 PM | ||
02-09-2025 02:20 PM |
New to the community? Here's some information to help you get acquainted:
01/27/2025: New firmware updates are available.
12/18/2024: New firmware updates are available.
EOS C300 Mark III - Version 1..0.9.1
EOS C500 Mark II - Version 1.1.3.1
12/05/2024: New firmware updates are available.
EOS R5 Mark II - Version 1.0.2
09/26/2024: New firmware updates are available.
EOS R6 Mark II - Version 1.5.0
Canon U.S.A Inc. All Rights Reserved. Reproduction in whole or part without permission is prohibited.