Unable to send print dataSupport Code : 5100 A printer error has occurred. Turn the printer off and then on again. If this doesn't clear the error, the printer needs repair. See the manual and contact the service center.The thing is . . . I have unpl...
I NEED HELP W/SAME MODEL, BUT FIRST A RESPONSE. I wondered the same thing about the 3620 when the scanner had a blank line. In the help section, it said the printer description includes the scanner. BUT I AM POSTING HERE FOR ANOTHER PROBLEM WITH ...
My printer is not loading the paper to print. But when I try to print it says that the paper is jammed. What can I do?
Help wanted ref to model TS3150 Just purchased and cannot find any drivers for it as it appears to be not compatable with my Windows 8 Pro 64 bit if only it stated it on the Box,,,, any help is most appreciated cheers
My Canon MX920 Printer I bought last year just randomly started printing blurry text, the last time I printed something on it was June 17 after that i haven't used it at all its been unplugged ever since I used it to print photos at a event I was wor...
I have a Canon MG2550 which won't print a full A4 sheet, it cuts off the last centimetre leaving a gap at the bottom of the page which is rather frustrating. I had given up on this printer but have now had to start using it again. I have gone throug...
So I've been getting this general Printer Error and I looked it up and it looked like the most common cause was bad/old ink. So I replaced all ink cartridges and now I get a new error! U052 incorrect print head it's not the incorrect print head, it's...
I can print normal stuff like pdf documents on plain paper. When I try to print a photo on glossy paper (4x6), the photo paper loads and you can hear the printhead working but the paper comes out blank. I run through the menu and adjust all the setti...
the Pixma iX 6820 is a very nice printer. However, my big complaint is that using "nonstandard" (non standard to Canon) paper sizes is a pain. Apparently even savng a file with all the print info doesn't mean that 4 or 5 steps aren't needed to use ...
Consistant use,, lovely, but unusable at the moment. Will print two or three pages and then dies.I hate the thought of calling canon, I'm sure the answer will be throw it away and buy a new one. any suggestions? I'm not real tec hie.Thanks
I have a Pixma 5700, 6 months old. When I turned it on this morning, all was normal, reset ready to pring. I sent a text to the printer and it acted normal, (all the normal noises) but when it came time to print it spit out blank paper. i checked the...
Is it possible to save a scanned text as a text file and not image (ipeg)?
I just bought an ip8750 printer to replace another ip8750. After printer head alignment there were some lines in the printed bars. On printing photos I could see some lines. I tried to do manual printer head alignment and saw that I needed to adjust ...
I have a Pixma TS9020. I have all new ink, but everything prints pinkish from the magenta cartridge. I have cleaned the print heads (3x), deep cleaned the print heads and ran the print alignment. No luck. The cartridges are new cannon and show a f...
When I turn on the printer, I get alternating zeros on the LED light, then after a while I get error code e06 witht the orangle alert lamp on. I cant print anything at all, please help.
| Subject | Author | Posted |
|---|---|---|
| 11-29-2024 01:32 PM | ||
| 11-28-2024 02:05 PM | ||
| 11-28-2024 02:03 PM | ||
| 11-28-2024 11:56 AM | ||
| 11-27-2024 05:16 PM |
New to the community? Here's some information to help you get acquainted:
09/26/2024: New firmware updates are available.
EOS R5 Mark II - Version 1.0.1
EOS R6 Mark II - Version 1.5.0
07/01/2024: New firmware updates are available.
04/16/2024: New firmware updates are available.
RF100-300mm F2.8 L IS USM - Version 1.0.6
RF400mm F2.8 L IS USM - Version 1.0.6
RF600mm F4 L IS USM - Version 1.0.6
RF800mm F5.6 L IS USM - Version 1.0.4
RF1200mm F8 L IS USM - Version 1.0.4
Canon U.S.A Inc. All Rights Reserved. Reproduction in whole or part without permission is prohibited.
