Camcorders
cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Posts

Canon GX10 AWB issue.

There is a very strange Automatic White Balance behavior of GX10. If White balance (WB) is set to AWB and I turn on a cam, sometimes it sets Day light WB instead of AWB. There is no sun icon on display of course. I have tried this in LED illuminated ...

vstrglv by Contributor
  • 10272 Views
  • 18 replies
  • 0 likes

Why do I get two files for every recording?

I'm shooting a 3-minute video in a studio with a Canon Vixa HF G50. It always generates TWO recordings. One recording is longer and the second recording takes over from where the first one leaves off. It's as if the first disc has run out of space so...

Elura 60 dead

I have no power either plugged in or full charged battery installed.new cr1616 installed as well.I saw on another forum discussion that there are micro switches on the doors for battery and card reader.Can anyone give me more info on that or any othe...

rrssllll by Apprentice
  • 1806 Views
  • 3 replies
  • 0 likes

Canon GX10 fan noise

I am going to purchase this camcorder but have some doubt  about it's fan noise. One question is about it's value during recording. Another question is about an operation mode when a fan works. It's clear that the fan works at 4K 60(50)fps. But what ...

vstrglv by Contributor
  • 4897 Views
  • 8 replies
  • 0 likes

XA11 PAL -> NTSC Conversion

Hello Canon Community! This may be a long shot and I think I already know the answer of 'no' for this.Was wondering if there's any way I as the end user of a PAL XA11 can convert the system to NTSC. Appreciate any and all insight.

JJAuer by Apprentice
  • 2416 Views
  • 1 replies
  • 0 likes

Canon XA40 'P' settings info

Sorry for all the newby questions and I have read the manual before asking. When the XA40 is set to 'P' mode is there a way to see what settings the camcorder is using, preferably on the LCD screen?

XH A1 Composite Output

Anyone know it is it possible to get the recording image rather than the viewfinder image? The knowledge base says yes, but the image shows two component terminals, while the camcorder really only has one. The purpose is to bypass the DV tape and rec...

raweber by Apprentice
  • 2239 Views
  • 2 replies
  • 0 likes

Vixia HV-30 battery mystery

I fully charge my batteries with the external Canon charger. When I check them with multimeter, they show a full 8V charge. When I put in camcorder, however, they drain in about 2-3 minutes. Then when I check the "dead" battery with multimeter again,...

dkbb12 by Apprentice
  • 2113 Views
  • 4 replies
  • 0 likes

XF400 C LOG 3 Exposure

How do you properly expose C Log 3 on the XF400/405? An additional external monitor with waveforms is not a viable option. The Zebras are limited to only 70% and 100%. Is it possible that Canon could add a waveform monitor or adjustable Zebras via fi...

Canon G60 Faint vertical noise banding in night videos!

Wondering if its normal or a defect? Thanks.You can faintly see it in this YT video- but the YT compression has mostly washed over it. The banding is vertical in the noise and NOT the circular banding around the moon. https://www.youtube.com/watch?v=...

Scurvy by Apprentice
  • 1374 Views
  • 2 replies
  • 0 likes

video transfer

I have a ZR25MC Camcorder. It is quite old but works perfectly. I would like to transfer my recorded videos to my laptop computer and then burn a DVD for viewing on a big screen TV. Can anyone tell me what cable connection I would need to transfer to...

Resolved! Audo Output on HF R800 Buzzes.

Our Church purchased a VIXIA HF R800 to record services and post on You Tube; Learning as we go; slowly making headway. Rigged up an external shotgun mic, which seems to work - but when I plug in a set of headphones to monitor audio input all I get i...

Getting started

New to the community? Here's some information to help you get acquainted:

Announcements