Printer Software & Networking
cancel
Showing results for 
Search instead for 
Did you mean: 

Posts

Canon MX870 to new Netgear R7900

Just installed a new Netgear X6 R7900 and attempting to connect my printers to the router. The HP works fine but the Canon Pixma MX870 shows as being connected (192.168.1.5) however the red light is on for the Port on the router and it will neither p...

Raydeo by Contributor
  • 2424 Views
  • 2 replies
  • 0 likes

Resolved! Set up MX450 for wireless access

I hope this doesn't get too complicated;I had a network set up with a Verizon DSL connect to a local home network.  I could never get the MX450 to be reognized , or connect to this network.I have since been upgraded to Verizon FIOS , have a new Fios ...

deshacn by Contributor
  • 7008 Views
  • 5 replies
  • 0 likes

MG2950 wireless connection

I have the Canon MG2950. I had connected wireless on my old router. But now I have a new router and I do not know what do I have to do in order to install again the wireless connection. Thank you in advance.

nicole1 by Apprentice
  • 2168 Views
  • 0 replies
  • 0 likes

Printer not connecting to phone

I have the Canon MG3520 and I tried connecting it to my phone and it won't connect to my phone at all. I tried adding the canon service app to see if it would work and nothing. What should I do? And how do I reset my printer?

Cannot setup wireless LAN on PIXMA MX922

I just bought the PIXMA MX922 and I can't complete the WLAN setup. Undert the Standard setup, when the printer searches for the wireless access point, I get the error message: "Access point was not detected." I then go into the LAN settings to check ...

Irvin432 by Apprentice
  • 3108 Views
  • 3 replies
  • 0 likes
Getting started

New to the community? Here's some information to help you get acquainted:

Announcements
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/30/2022: Service Notice: EOS 70D: Error 70 or Error 80
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
03/16/2022: New firmware version 1.5.2 is available for EOS-R5
03/16/2022: New firmware version 1.5.2 is available for EOS-R6
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.1.1 is available for EOS-R3
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!
12/7/2021: New firmware version 1.3.0 is available for Mount Adapter EF-EOS R 0.71x
12/7/2021: New firmware version 1.1.1 is available for CR-N 300
12/7/2021: New firmware version 1.1.1 is available for CR-N 500
12/2/2021: New firmware version 1.1.0 is available for RF 70-200 F4 L IS USM