cancel
Showing results for 
Search instead for 
Did you mean: 

430EX II Speedlite Attachment

hp_chic
Apprentice

Hi Guys,

 

Are there any professionals here who know if connecting the 430EX II when it and the camera (T5i) are both ON damages anything? I know that the user manual says the Speedlite should be OFF before attaching it to the hot shoe. I failed to follow that guideline several times before I read the manual... just wanna make sure.

 

Thanks.

1 ACCEPTED SOLUTION

MikeSowsun
Authority

It is probably a good precaution but I doubt you will cause any damage if you leave the power on.  

 

I have been using Canon cameras and flash units for over 30 years.  I never turn off the camera or flash when I attach them or take them off, and have not had any problems of any kind.

 

I just went through a few of my older manuals and discovered that while newer flash units like the 600EX, 430EX II. 270EX, 270EX II, 320EX, and 90EX all say to turn off the power while attaching the flash,   older units like the 580EX II, 430EX, 420EX, etc, do not have this warning. 

 

Mike Sowsun
80D, 5D Mk III

View solution in original post

4 REPLIES 4

MikeSowsun
Authority

It is probably a good precaution but I doubt you will cause any damage if you leave the power on.  

 

I have been using Canon cameras and flash units for over 30 years.  I never turn off the camera or flash when I attach them or take them off, and have not had any problems of any kind.

 

I just went through a few of my older manuals and discovered that while newer flash units like the 600EX, 430EX II. 270EX, 270EX II, 320EX, and 90EX all say to turn off the power while attaching the flash,   older units like the 580EX II, 430EX, 420EX, etc, do not have this warning. 

 

Mike Sowsun
80D, 5D Mk III

It never even dawned on me to consider turning them off before attaching/removing.  But what do I know, I'll swap lenses without turning off my camera if I'm tethered.

hp_chic
Apprentice

Thanks!

AllNoAll
Contributor

I think this advice by Canon in your manual is an extreme precaution on their part. With my little knowledge of electrical theory it is possible to cause damage if both units are on but you would have to be moving extremely slow; basically there is an extremely small chance that when the two unit get very close to each other without a solid connection the small amount of electricity that could be present at each contact could arc causing a power surge in either or both units. With how little amount of electricity is present it is extremely unlikely this would ever happen.

Announcements
06/30/2022: Service Notice: EOS 70D: Error 70 or Error 80
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
03/22/2022: New firmware version 1.2.0 is available for PowerShot PICK
03/16/2022: New firmware version 1.5.2 is available for EOS-R5
03/16/2022: New firmware version 1.5.2 is available for EOS-R6
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.1.1 is available for EOS-R3
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!
12/7/2021: New firmware version 1.3.0 is available for Mount Adapter EF-EOS R 0.71x
12/7/2021: New firmware version 1.1.1 is available for CR-N 300
12/7/2021: New firmware version 1.1.1 is available for CR-N 500
12/2/2021: New firmware version 1.1.0 is available for RF 70-200 F4 L IS USM