Printer Software & Networking
cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Posts

Image Garden scans gone

I've had my Pixma printer for some time and have scanned a lot of photos and documents.  Always before when I scanned something it went into the Image Garden and all the other things I had scanned showed up there, too.  Yesterday I opened Image Garde...

G3200 cannot detect printer during setup

When attempting to install my G3200 printer software, I reach a point where I am directed to connect and turn on the printer. It is then that I connect and turn on the printer. It detects the printer for a few minutes then says printer cannot be dete...

Hugh by Apprentice
  • 199 Views
  • 1 replies
  • 0 likes

Toner Status for MF641Cw

I am unable to get the Toner Status version 2.10 program to run for my Canon MF641Cw on my desktop computer. My operating system is Windows 10 Home 64-bit version 21H1. I reinstalled the Toner Status software and it still will not run.

Drawde by Apprentice
  • 252 Views
  • 2 replies
  • 0 likes

Print on Home G7020 from the Road

I have a Pixma G7020 printer on my home network.   When I travel I have a Windows laptop.    Would like to print over the internet to my home printer.   I have searched and searched and cannot come up with an answer.  Seems pretty basic and was easy ...

tomlay by Apprentice
  • 226 Views
  • 4 replies
  • 0 likes

PIXMA MG2260 Unable to Install Software

I have tried to set up my Pixma 2260 printer, I keep getting an error message when I try to download the driver or software.....I've turned off my firewall, as well as AdBlocker....I'd really like to use my new printer, suggestions?

Tbone55 by Apprentice
  • 191 Views
  • 1 replies
  • 0 likes

Phantom MF642 in Linux.

I installed my printer in Linux using the Linux UFRII 5.40 driver. After installing the driver, I used the cnsetuputil2 program to register the printer with CUPS. When I attempted to print, the printer asked for A4 paper instead of letter (I'm in the...

Getting started

New to the community? Here's some information to help you get acquainted:

Announcements
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available forRF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!