cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

C200 .CRM Corrupt file? Anyway to Combine .DAT & .DMV?

loggylunch
Apprentice

Hey there,

 

Was recently shooting Canon Raw Light. Camera died whilst shooting, and the C200 did not combine the raw light data files for the actual video file. All I had on the memory card was a 1) .DAT fle and 2) a .DMV file.

 

Screen Shot 2018-05-27 at 12.48.40 PM.png

 

Is there anyway possible to combine these or recover the video on them?? It seems like it should be a pretty simple fix/script to remedy. 

1 ACCEPTED SOLUTION

Alex_Flamsteed
Apprentice

I just had the same problem. Try puting the card back in the camera and watch media on the camera. It will come up with a question mark. When you try play the clip it should give you the option for recover the clip. 

 

This worked for me! Good luck. 

 

Alex.

View solution in original post

7 REPLIES 7

Alex_Flamsteed
Apprentice

I just had the same problem. Try puting the card back in the camera and watch media on the camera. It will come up with a question mark. When you try play the clip it should give you the option for recover the clip. 

 

This worked for me! Good luck. 

 

Alex.

@Alex - you ABSOLUTE LEGEND. Saved me. Thank you!!

Dockojoon
Apprentice

Same problem here.

Using the camera to recover files is working, but it its slow, because it need to click one clip per time.

Alex_Flamsteed
Apprentice
That’s good that it’s working, I only had one corrupt file thankfully.

jemadd68
Apprentice

Worked for me too! Thanks!

ISABELA
Apprentice

Is there an option to recover the .CRM film file without in camera recovery? The original SD card was formatted so I only have access to the .DAT & .DMV file on the computer. Any suggestions? Thanks!

Hi everyone,

Re-opening this thread, I have a few corrupted .CRM files that were shot on the C300 MK III. The original media card has been formatted so the in-camera repair solution isn’t an option. As Isabel, I’m looking for a software solution to fix these .CRM files. They won’t open in Premiere or the Canon RAW utility. Any information would be appreciated! Thank you! 

Jae

Announcements
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
10/14/2022: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!