08-02-2014 02:36 PM - edited 06-05-2016 01:37 PM
Could not complete driver installation during brand new set-up because of this message. Went through wirless connection set-up several times and connectivity was always present. Logged into my D-Link 626L router and could see the printer connected but the ip address referenced was 0.0.0.0. Tried to assign a static ip address through set-up on the printer and also use the cmd prompt in windows, all to no avail.
Called Canon Support and these 2 setting changes solved the problem:
1) Disable the Wirelss LAN DRX setting
2) Disable the IPv6 Setting
This article explains how to adjust the settings on the printer.
Solved! Go to Solution.
08-05-2014 04:48 AM
Hi mimiaz58,
Thank you for sharing!
01-05-2017 04:31 PM
I have mg3660 that isn't connecting wirelessly either. I wish I had bought a LCD screen one as it's so much easier!!! I will try and add the Mac address of the printer to my security setting in my router (netgear) and see how that goes. Why do they make it so difficult?? I tried the ubiquitous connection but it said it could not find the port and I could not create a port for it when I searched for the solution. In very disappointed in Canon. Let you know how I go.
01-05-2017 07:22 PM
After 40mins of Canon phone support I got an ip address! Had to press the dps button on my router and also extend my ip address range on my router. Used the main setup software and it took a while and even if it failed to detect printer at first just keep going until I connected using the usb method. Disconnected when it told me to and it then set up the connection to my router. Successfully printed from ipad, laptop after it got an ip address. In short, just call their support line and hope you get someone good.
01-06-2017 06:11 AM
Sorry for the spelling mistakes. Meant to say I pressed the wps button for five seconds on my router after I pressed the Wi-Fi button on my printer until the power light and Wi-Fi were flashing. I had to restart my router after the Wi-Fi blue light kept flashing. After that I did get an ip address. I had to restart my laptop after tried the set up as it failed to detect the printer. It does take a while but eventually my laptop picked up the Wi-Fi when I ran the master setup and chose the Wi-Fi using usb method. Hope this helps a little.
07-11-2017 11:41 AM
This did not work for me. I have 2 other computers that communicate fine with this printer. Any other thoughts?
07-17-2017 02:48 PM
This article was very helpful. After executing the steps mentioned my printer connected seamlessly. Canon should include these helpful solutions in their printed directions that come with the printer. This experience left me with a negative opinion of Canon. I'm so frustrated and so mad at Canon. I wasted so much time.
01-04-2018 12:49 AM
02-10-2018 09:34 AM
I had the same problem. In my case I had an IPV4 address registered on the printer. I disabled IPV6 but it didn't help, still got "Printer Not Detected"
Finally after much trial and error I found a setting that I had disabled in the printer called "Enable WSD Scan from this Device". This was in the WSD settings. When I enabled this setting, then the setup wizard was able to find the printer
03-21-2018 04:48 PM
I've tried this solution and it did not work for me. I've been using my MX922 for about 2 years now and all of a sudden it stopped working and I can't detect it in my network. I am running Win10 64 bit.
Any help would be greatly appreciated.
09-03-2018 08:10 PM
Thank you for sharing! I only had to disable the IPv6 Setting and not the LAN DRX setting so others may just start with IPv6 first and only change the other if necessary.
10-15-2018 03:37 PM
Printer will not detect my network. Entered the network name directly and still no luck in detecting the network. Printer was working ok before I went on vacation.
07/01/2024: New firmware updates are available.
06/06/2024: New firmware updates are available.
EOS R6 Mark II - Version 1.4.0
Speedlite EL-5 - Version 1.1.0
Speedlite Transmitter ST-E10 - Version 1.1.0
04/16/2024: New firmware updates are available.
RF100-300mm F2.8 L IS USM - Version 1.0.6
RF400mm F2.8 L IS USM - Version 1.0.6
RF600mm F4 L IS USM - Version 1.0.6
RF800mm F5.6 L IS USM - Version 1.0.4
RF1200mm F8 L IS USM - Version 1.0.4
03/26/2024: New firmware updates are available.
Canon U.S.A Inc. All Rights Reserved. Reproduction in whole or part without permission is prohibited.