cancel
Showing results for 
Search instead for 
Did you mean: 

Maxify MB5320 How do I make a duplex document flippable ( reverse side upside down)

blockie
Contributor

I have a 40 page docuiment, in landscape mode, that I duplex. The doc. will be placed in a binder and when the reader reads it he/she will flip the pages top to bottom. I wish to print the reverse side of each page  upside-down so the reader will not have to continually turn the binder over. How?

1 ACCEPTED SOLUTION

I used "Nuance PDF Pro" and was able to make the back of the page reversed (flippable). Satisfied my needs.

View solution in original post

5 REPLIES 5

deathtocannon
Apprentice

This is what my piece of junk does automatically and I have no idea how to stop it. Send me the postage and I will send you the printer in the post as I never want to touch the crappy thing again!!

Sorry to hear that you dislike the Maxify. I purchased the MB5320 because it had two input cassettes and am very pleased with it.

Somehow I got the flip (back) side to reverse (probably advice or hint from a good Samaritan..Maybe I fooled around with the printer properties. Lot'sa capability's there.

I encourage you not to give up. In your case, I suspect that you had fooled around with the properties and  inadvertently set the wrong function. Take time to figure that out and you'll find that the reverse of what you did will turn that function on and off. I am beginning to remember that it may have had something to do with "booklet".

Incidentally, in May of this year I fell and spent the next 4 months in rehab. During this four months the printer was left on and when I was able to use it again it worked without error.. A testament to Canon.

 

Bill

I used "Nuance PDF Pro" and was able to make the back of the page reversed (flippable). Satisfied my needs.

I have set both the MAXIFY MB5320 Printer and my laptop (2 feet away) to the same network.  Both are contfirmed on the same network. The computer connects to the internet, but the printer does not see a server although they are on the same network. I cannot wirelessly print to the printer from the computer. I can print using a USB cable.. If I use the printer 'ACCES POINT" and put the computer to that access point I can wirelessly print. However, the computer does not see the internet then.

Long story short;

1. Computer set to network and internet.

2. Printer on same network but doesn;t connect to computer to print wirekessly.

3. Printer and computer can communicate via USB cable but not wirelessly.

HELP??

 

Bill

This can probably be answered with a phone call. Does anyone have the # to Maxify support?
Announcements

08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/30/2022: Service Notice: EOS 70D: Error 70 or Error 80
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!
12/7/2021: New firmware version 1.3.0 is available for Mount Adapter EF-EOS R 0.71x