cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

CanoScan 9000F Mark II installation

matthewfox
Apprentice

It's probably me... but I'm finding it a real pain to install the CanoScan 9000F Mark II. First of all I (accidentally?) installed an older version of Canon IJ Scan Utility. However, that had a button labelled "ScanGear". When I install Canon IJ Scan Utility2 (v 2.3.5), that button is replaced with "Driver" and I have limited options to scan.

 

I have also installed Canon IJ ScanGear Starter EX but when I load this, I get an error:

 

Cannot communicate with the scanner for these reasons:

 - Scanner turned off

 - USB cable is disconnected

 - A scanner driver supporting this software is not installed

 

And it's driving me crazy!

 

I'm running macOS Mojave 10.14.4

 

Any help would be appreciated.

2 REPLIES 2

Caemene
Rising Star

Hi matthewfox,

 

The Canon IJ Scan Utility 2 that is installed should have "Driver" titled on the last scan button. Within that Driver option, you should have two tabs at the top stating Basic and Advanced giving you additional scanning options.

 

To resolve the scanning error messages that you are receiving I recommend downloading and installing the ICA Driver from the Canon website, click HERE to access that driver. Once the ICA driver has been installed onto your computer, open the program Image Capture. This is a Mac supported scanning program. In the upper left corner locate "Devices" and "Shared" by each of their titles, there should be a number, hopefully, 1. Hover over the number to ensure that the CanoScan 9000F Mark II is detected. With the scanner detected, perform a scan. In the event that the scanner is not detected. Restart the computer and scanner, attempt the scan again.

If I open Canon IJ Scan Utility 2 and click Driver I get this:

Attach 1.png

 

But if I choose Canon IJ Scan Utility I get all these options with the Basic and Advance tabs you mentioned

 

Attach 2.png

 

Surely I should have those advanced options in Canon IJ Scan Utility 2???

Announcements
01/18/2023: New firmware version 1.1.1 is available for EOS R6 Mark II
01/09/2023: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
01/03/2023: Welcome to CES 2023!
12/08/2022: New firmware version 1.0.5.1 is available for EOS C70
12/07/2022: New firmware version 1.7.0 is available for EOS R5
12/07/2022: New firmware version 1.7.0 is available for EOS R6
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/14/2022: New firmware version 1.0.1 is available for CR-X300
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.