cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Camera locks up, recording message

deborah1
Apprentice

I just bought a T6s and have a strange problem (I hope it's a simple answer!). I can take one picture and then it locks up and I cannot take another. The message on the LCD monitor is "Recording..." "Remaining images: 1" with the continuously circling ball. It's as if it can't record. We formatted the card. So I'm not sure what's wrong. When my husband first got the camera, he ussed it for a few days without any problem. This just started today.

30 REPLIES 30

Is it possible that you accidentally turned on the card's "write protect" switch?

Bob
Philadelphia, Pennsylvania USA

Waddizzle
Legend

It almost sounds like the camera is in video mode.  But, if it is telling you that there are "remaining images..." then it is likely in a multiple shot mode, such as in-camera HDR.

 

Mulitple shot mode can be a one-time affair, or a repetitive mode where every "single shot" you take actually requires you to take multiple shots of the same image.  Check your menus to make sure that multi-shot or HDR modes are not active.

 

Until you finish the required number of shots, then the camera could be busy processing the previous shots.  I can see the camera "hanging" if your multiple shots are not at all similar.

--------------------------------------------------------
"The right mouse button is your friend."

After having the problem, we took the SD card out and used into another Canon camera, and we had no issues. You could get our T6 to work with the card after an error message by taking out the battery and putting it back in to "reset" it. But after awhile, the error would occur again.  I ended up taking the camera back to the store. And the Canon guy, after observing this process, said that the error message number meant it was a problem with the SD card. Though he offered to replace the camera, we decided to replace the card and see how it goes over the next few days. Weird - especially since we used the card  -- it was brand new -- in another camera and it was OK. Thanks for the help!

 

 

BAS_CanonShoot
Contributor

I am having the same issue. It isn't consistent, but seems to increasing become more of an issue.

Camera: Canon EOS Rebel t6s

 

The problem: When I take one picture, the camera reads, "Busy", the remaining pictures number starts to blink "999", and the red light remains solid. This doesn't stop when I turn the power switch to off, but rather it changes to saying "Recording... Remaining images: 1", the blinking number stops, but the red light remains.

 

I have tried using multiple different SD cards and have come to the same conclusion. 

 

I have tried erasing all the settings (i'm assuming that is back to factory settings) and still have the same issues.

 

Varying results occur when I take the SD card out, turn on write protect put it back in the Camera, turn on the camera, get the error that the card is protected, turn off the camera, take the card out and turn off write protection, replace the card back in the camera. I can then (sometimes) get the camera to take one or two photos before then reverting back to the above issue.

 

My questions are:

 

Has this happened to more than just the two people who have posted here?

 

Has there been a fix found?

 

Do I need to send my camera in for support/fix?

Check the multiple exposure and HDR settings inside of the camera.  They should normally be disabled for single exposures.

--------------------------------------------------------
"The right mouse button is your friend."

BAS_CanonShoot
Contributor
Where would I find those settings on the T6s?

And let's say those settings are turned on? Should it really take more than a minute to process? More than 5 minutes? 10 minutes? (That's how long I am giving it before I unlactch the battery and start over)

Thank you for helping us troubleshoot this issue!

BAS_CanonShoot
Contributor
Is there a recommended SD Card that we should try?

What shooting mode is the mode dial set for?  Make sure it is not "HDR Backlight Control" mode, see page 27 of your Instructional Manual.  You can download a manual if you do not have the original handy.   The following is from page 7.

 

T6s_SD_Cards.PNG

 

I would recommend using a Class 10 card, 64 GB or less.  A 16 GB card would be ideal for just photos saved as RAW.

--------------------------------------------------------
"The right mouse button is your friend."
Announcements
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
10/14/2022: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!