My new HP computer doesn't recognize my Canon MX330 printer. It was working fine on the old one.
When I try to "Add a printer" it doesn't even show up as an option even though everything is plugged in and the printer power is on.
When I try to "Add a printer" it doesn't even show up as an option even though everything is plugged in and the printer power is on.
Tried several deep cleanings but same problem. Nozzle check indicates Cyan isn't ptinting. Plenty of ink in the tank.
I have a canon MG 2922 and it will only print a logo on the top left and a gray line in the center and two signatures. I have cleaned it and there is plenty of ink....HELP...need to print out water report for the state....thank you nana8
The scans on my PIXMA MX 340 are now blurry. I am using an Apple computer, if that matters. Can you help?
I have an Pixma MX882 with the Error U052 message and have tried all the solutions on this site to no avail! Any suggestions/solutions?
Hi, I am trying to print draft copies of documents and images in grayscale from my IMAC but the feature is turned off on my printer and it does not appear anywhere as an option that I can select. Can you help IMAC OS X 10.11.3 I have followed your...
Hi, I am using Windows 10 on 2 PCs. I can print to the printer OK and tell the scanner to scan a document via Windows tools - So the connection is OK. I have installed MP Navigator 5.02 on both PCs - It opens on 1 PC but on the other it says "Cannot...
Hello, I am using windows 8.1. My printer is displaying "printer offline" status and it clearly is not. I have checked to see if it the "use printer offline" mode was checked and it is unchecked. I downloaded and installed the recommended drivers acc...
I turn it off and on like the manual says, but the same error 6000 message keeps appearing. Please help.
Is it possible to print on printable CDs using a Pixma MX392 and if so how and if not, could you recommend an economical model that can print on CDs?
My MX920 often takes a long time to respond after power up - anywhere from 5 minutes to half an hour. It is wireless, with AT&T network. I am running windows 7. This problem seemed to have started shortly after I downloaded the latest version of Acro...
I have a MG3100. Has been print just fine. When I copy - its copies just fine. When I print something - most of the page will print just fine and sections of it the lines are wavy, don't connect or just difficult to read. Had my computer wo...
my printer is pixma mx922when i print,there is a problem code 6001;-it told me 1/ shut down printer 2/ open and shut the papper case and try print.. again...1.but i can not fix it...so tell me how to fix it...?
I am trying to put a stack of docs in the ADF and then scan them into individual pdf or jpg files. No matter what I do, I can not make this work. Can someone please step by step me through the setup of this? Thank you. Tom
how do i make my canon printer work with windows 10.1
Subject | Author | Posted |
---|---|---|
12-10-2024 10:26 PM | ||
12-10-2024 06:04 PM | ||
12-09-2024 09:51 PM | ||
12-09-2024 05:36 PM | ||
12-09-2024 01:47 PM |
New to the community? Here's some information to help you get acquainted:
12/05/2024: New firmware updates are available.
EOS R5 Mark II - Version 1.0.2
09/26/2024: New firmware updates are available.
EOS R6 Mark II - Version 1.5.0
07/01/2024: New firmware updates are available.
04/16/2024: New firmware updates are available.
RF100-300mm F2.8 L IS USM - Version 1.0.6
RF400mm F2.8 L IS USM - Version 1.0.6
RF600mm F4 L IS USM - Version 1.0.6
RF800mm F5.6 L IS USM - Version 1.0.4
RF1200mm F8 L IS USM - Version 1.0.4
Canon U.S.A Inc. All Rights Reserved. Reproduction in whole or part without permission is prohibited.