cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Does not copy and scan using ADF

jaims
Apprentice

Hi everyone!

 

I would just like to ask if anyone knows how to fix ADF of G4000. The printer does not accept documents to copy or scan using the ADF

 

Thanks!

1 REPLY 1

BillS
Mentor

Hi jaims,

 

To scan a document at optimum quality, load it on the platen glass.  If you prefer to use the document feeder:

  1. Make sure that any original has been removed from the platen glass.

  2. Open the document tray.

  3. Insert the document in the document tray until you hear a beep sound.

    Load the document WITH THE SIDE TO SCAN FACING UP in the document tray.

    Note

    • For details on the supported originals, see below.

    • When you set the alarm to be silent in Sound control of Dev. user settings, the alarm will not beep even if the document is inserted in the document tray.

  4. Adjust the document guide (A) at the front of the printer to match the width of the document.

    Do not slide the document guide too hard against the document. The document may not be fed properly.

This didn't answer your question or issue? Please call or email us at one of the methods on the Contact Us page for further assistance.

 

Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Announcements
01/18/2023: New firmware version 1.1.1 is available for EOS R6 Mark II
01/09/2023: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
01/03/2023: Welcome to CES 2023!
12/08/2022: New firmware version 1.0.5.1 is available for EOS C70
12/07/2022: New firmware version 1.7.0 is available for EOS R5
12/07/2022: New firmware version 1.7.0 is available for EOS R6
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/14/2022: New firmware version 1.0.1 is available for CR-X300
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.