cancel
Showing results for 
Search instead for 
Did you mean: 

PIXMA MG3620 Windows 10 won't set up properly

JIMDI
Apprentice

Have tried to set this printer up numerous times by different methods with no luck. It prints but takes a long time to print.

If I go into troubleshooting it doesn't find any problems. The Windows printer test page says it was correctly installed.

If I go into the IJ utility under status it says not found and certain settings can't be used. Spent many hours but no success.

Please help.

3 REPLIES 3

Patrick
Product Expert
Product Expert

Hi JIMDI,

 

Are you using your PIXMA MG3620 wirelessly?   or with a USB cable?

 

When you mentioned the IJ Utility, are you referring to the IJ Scan Utility?

 

What is the exact error message that you get when attempting to use that utility?

 

 

 

Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.


@Patrick wrote:

Hi JIMDI,

 

Are you using your PIXMA MG3620 wirelessly?   or with a USB cable?

 

When you mentioned the IJ Utility, are you referring to the IJ Scan Utility?

 

What is the exact error message that you get when attempting to use that utility?

I printing wirelessly. No cable

I was trying to use the IJ printer utility . Is that only for Macs? If so maybe that is why it isn't working properly.

I am not presently at the location for the printer so don't feel I can proceed at this point.      I do have the Windows Printer Test Page and the Network Configuration page with me and it says it is using a Type 3 User mode driver 2.90.2.10. Is this the correct driver? At one point during the setup it said it couldn't load the MP drivers.

 

 


 

Hi JIMDI.


The IJ Printer Utility is installed automatically by Windows, through the Windows 10 App store, when it detects a Canon inkjet printer on the network or connected by USB.

 

Patrick was referring to the "IJ Scan Utility," which comes bundled with the drivers developed by Canon.  If the IJ Scan Utility is not present, then you may find the Canon-produced drivers on the MG3620 Drivers & Downloads page.  The minimum necessary installation is the MG3600 series MP Drivers.

 

If the drivers do not install correctly, then your computer may be in S Mode.  Refer to Microsoft's support for Windows for more information on S Mode.

 

Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Announcements

08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/30/2022: Service Notice: EOS 70D: Error 70 or Error 80
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!
12/7/2021: New firmware version 1.3.0 is available for Mount Adapter EF-EOS R 0.71x