cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

EL-1 speedlite on-camera power when using multiple speedlites

luckyone
Apprentice

I am not the smartest guy when it comes to using multiple flashes. And I find the Canon instructions confusing, to say the least.

I have three Canon speedlites, including the EL-1. I want to use one of the speedlites on camera, and the other two off-camera. I am able to get that to work, but am confused about how to set the exposure level or power for each unit.

I think I have figured out how to set it for the two off-camera units, but how do I know the level for the on-camera unit.

For example, maybe I want to set one off-camera speedlite to full power (100%) or the 0 level, and one to half power (50%) or the minus one level.

But what is the level of the on-camera speedlite? Can I set that? Is it always 100%?

Also unsure, if I should be using A:B, A:B:, or G (groups).

Any help will be appreciated. Or point me to a good online video or tutorial. Thanks!

3 REPLIES 3

kvbarkley
VIP

What mode are you using? If ETTL, the camera will adjust the flash level as a result of the pre-flash, so you don't know the actual flash power. You can use manual flash if you want total control.

Thanks for the quick reply.

I am experimenting with ETTL, and manual, and also G (group) settings.

I would like to use a speedlite off-camera (umbrella or softbox on a light stand) as my main light, another speedlite on the background, and the EL-1 on camera as a fill light. For example, maybe I want the umbrella speedlite at full power, the background speedlite at 1/2 power (or minus one-stop), and the EL-1 on-camera 1/4 power (or minus two-stops, so I don't overpower the main light.

Should I be using A:B, or G (group settings), or something else? I am assume that A and B would be the two receiving speedlites, and there is no letter for the sender. Is that right?

I see how to set the power of the receiving speedlites, but in this case, how do I control the power output of the sending EL-1.

Any tips or guidance for the best way to achieve this will be greatly appreciated!

Sorry if this is confusing, but that is only because I am a bit confused. 🙂

halocastle
Contributor

You've indicated in your layout that you want to use manual power settings.  You can do this in manual mode and A:B C.  The unit on the camera is always part of the A group.  Just assign the other two units to groups B and C.

Group mode is overkill in your case: it's great for mixed setups where maybe you'd want manual (e.g. hair) and TTL (fill) together.

Announcements
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
10/14/2022: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!