cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

ADF printing problem - MX922

Dukek1
Apprentice

MX922 has worked fine for over a year but now printing from platen works fine, but any copying involving the adf shows a black line down the left side of every sheet printed. Did all the cleaning from the menu, but problem persists - single sheets copied via the platen are fine and every sheet copied via the adf has the black line.  Any help would be appreciated. 

7 REPLIES 7

James_C
Moderator
Moderator

Hi Dukek1,

 

Click HERE for instrucdtions to clean the PIXMA MX922 ADF.  This should resolve the issue you have described.

 

If you continue to have difficulties, please contact our support group using the following link:

http://Canon.us/ContactLI

Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

James C thanks for your response, but I could not open the citshome.cits.canon.com - server address could not be found. I did click on the support group link and left a message there.  Thanks for your help.

Hey there, Dukek1!

 

Apologies for the confusion, the link went to an internal technical support resource. I've attached a PDF of the file to this post. We hope this helps!

 

 

Stephen, thanks for the help. I had previously tried what is shown in the pdf to no avail. I ended up calling your sales dept and ordered a new MX922 under your Loyalty Program.

When the new one  is setup I 'm going to take apart the old one to try my hand at a fix for a back up. My wife is laughing at me already !

I am having this problem now too! I have cleaned the ADF and the scanner glass multiple times. I have actually done all of the cleaning and nothing has worked.

Please let me know what I can do to get rid of the black line.

Hi kimday,

 

If you scan using the scan glass (instead of the automatic document feeder), does the line appear?

 

 

 

Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

No, it was only when using the auto doc feeder. I called Canon yesterday and spoke with technical support. The rep instructed me to clean as I had already seen online and done several times. After hanging up, I decided to see what happened when I scanned 20 pages through the ADF, instead of just 1, which is what I had been doing. Sure enough, the black line on the left about 1.5 inches from the paper edge was gone! I couldn't believe it, but I can now scan only 1 page and there is no line.

Announcements
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
10/14/2022: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!