cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Rebel t3i

30pointr
Apprentice

I recently purchased a canon rebel t3i , can I use a promaster FTD 5600 external flash

3 REPLIES 3

TCampbell
Elite

That's a very old flash.  The center pin and ground plate on the flash (or if the ground plate is plastic, there will be a little metal contact on one side which contacts the metal rail on the hot-shoe) are the key pins... when you close that circuit, the flash will fire and will release a trigger voltage into the camera.

 

That voltage needs to be 6v or LESS.  Damage could occur if it is greater (and there are a lot of old flashes for which that voltage is greater.)

 

You can find a list of trigger voltages as measured and submitted by individuals (hopefully accurately -- but this is the Internet) here:  http://www.botzilla.com/photo/strobeVolts.html

 

They don't list your Promaster FTD 5600 but they do list other Promaster FTD series flashes and of those listed, they all appear to be in the safe range.  If you own a multi-meter, that page has instructions on how you can test your flash before attaching it to your nice new camera.

 

Another thing to point out is that since that's a very old flash, it can only be used manually (and it's manual function isn't even all that great because you can't dial the specific power level output that you want) or via the Thyristor circuit.  Thyristors measure the light returning after bouncing off your subject.  They highly suceptible to be wrong depending on how large or how reflective your subject is.  Modern E-TTL II flashes are vastly improved and I'd strongly consider an upgrade.  Take a look at a Speedlite 430EX II -- which would be a great external speedlite for use on a T3i.

 

Tim Campbell
5D III, 5D IV, 60Da

6V, is it really that low for the t3i?  I can't say I've actually tested it, but my old 400D had a max limit of something like 250V.

I confirm 6V is too small for me better is 12V

 

 

 http://canon-eosrebelt3i18mp.blogspot.com

 

 

Announcements
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
10/14/2022: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!