10-28-2022 10:21 AM - last edited on 11-09-2022 08:26 AM by Danny
Hello everyone. I recently bought my first full-frame camera (Canon EOS R) and I have some questions that I haven't been able to find online.
I just recorded a job in C-LOG 8 bit, but when I transfer it to my pc, it comes in mp4 format. Is it normal? I always thought that Log footage would come in a filme such as video.clog or something similar. Am I wrong? This question emerged because I was editing my flat footage on premiere and it felt like the dynamic range was short and something was off - it was when I checked and saw the footage in mp4.
Can anyone help explaining it to me?
Thank you 🙂
10-28-2022 08:46 PM
The EOS R is only capable of recording movies in the MP4 format, so yes, this is normal. Canon Log offers a dynamic range of approximately 800% at ISO 400 or higher. Manually setting the ISO speed to 100–320 will make the dynamic range narrower.
10-29-2022 04:36 AM
Log is not a video format -- it's a gamma curve. A video format -- like MP4 -- saves pixels, which are just numbers, in a file. The gamma curve, whether it's Rec 709 or Log or whatever, dictates what those numbers mean.
In other words, changing from Rec 709 to Log will not change the file format; it will only change how the pixels in the file are encoded. It's up to you to decode those pixels correctly in post. Generally, a video editor will assume that your pixels are encoded in Rec 709; normally you would add a LUT to your footage to correct it from Log to Rec 709. You can find the official Canon LUTs for this here: www.usa.canon.com/support/p/eos-r (look for "Canon lookup table Version 201911").
Generally you want a 3D LUT, and 65-point grid is best. So to decode Log 3 to Rec 709, for example, you would use "3dlut\65grid-3dlut\full-to-full-range\CinemaGamut_CanonLog3-to-BT709_WideDR_65_FF_Ver.2.0.cube".
Note that to get the benefit of Log, do your exposure correction BEFORE applying the LUT. For example, in Premiere Pro, under Effect Controls, I would add a Lumetri Colour effect to fix the exposure, and then add another one with the LUT BELOW it in the control panel.
Hope this helps.
11-08-2022 01:24 PM
Thank you. Can you download Canon LUTs you listed here: www.usa.canon.com/support/p/eos-r (look for "Canon lookup table Version 201911") in Premiere Pro or is this for your camera?
11-08-2022 03:44 PM
LUTs are a standard format. They should work in just about any video editing software, and can even be loaded into devices, such as monitors which have LUT support.
Some cameras can also take user-loaded LUTs; but Canon cameras generally have the correct LUTs pre-loaded. So when you turn on View Assist in a log mode, the LCD shows corrected footage.
05/18/2023: New firmware updates are available.
EOS Rebel T100 - Version 1.1.0
EOS 5D Mark IV - Version 1.4.0
EOS 6D Mark II - Version 1.2.0
PowerShot Elph 360HS - Version 126.96.36.199
PowerShot SX420 IS - Version 188.8.131.52
PowerShot 620 HS - Version 184.108.40.206
PowerShot SX720 HS - Version 220.127.116.11
PowerShot G1X Mark III - Version 18.104.22.168
PowerShot G7X Mark II - Version 22.214.171.124
PowerShot G9X Mark II - Version 126.96.36.199
04/20/2023: New firmware version 1.4.1 is available for EOS R3
03/30/2023: New firmware updates are available.
EOS 1DX Mark III- Version 1.7.1
Speedlite EL-1 - Version 1.0.2
03/30/2023: Product Advisory for EF50 F1.2 L USM
03/30/2023: Product Advisory for EOS R10
2/07/2023: New product announcements!EOS R8 EOS R50RF-S55-210mm F5-7.1 IS STMRF24-50mm F4.5-6.3 IS STMRF15-30mm F4.5-6.3 IS STM
Canon U.S.A Inc. All Rights Reserved. Reproduction in whole or part without permission is prohibited.