cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

MG 2922

heinhtetoo
Apprentice
I bought that printer yesterday and I did set up as on the instruction paper.
After that, I did test print and the dialogue box showed SUPPORT CODE 6000. On the printer, green and orange lights were flashing alternately 3 times. I searched about alternate 3 flashes but it didn´t work. I also tried plug out and plug in several times. Please help me......
2 REPLIES 2

James_C
Moderator
Moderator

Hi heinhtetoo,

 

This message may be resolved by resetting your PIXMA MG2922.  Please follow these steps:

 1.  With the printer powered on, open the cover.  The ink will move to the left hand side.

 2.  Push down on the end of the black cartridge.  A clicking noise will be heard.

 3.  Slide the cartridge out of the holder towards you.

 4.  Push down on the end of the color cartridge.  A clicking noise will be heard.

 5.  Slide the cartridge out of the holder towards you.

 6.  Once both cartridges are removed, unplug the power to the printer (without turning it off).

 7.  Reconnect the power cord.

 8.  Turn on the printer.

 9.  Open the cover.  The carriage that holds the ink will move to the left hand side.

10.  Make sure the orange cap is off of the bottom of the black cartridge.

11.  Place the black cartridge in the bottom of the printer.

12.  Slide the black cartridge back until is cannot go back any further.

13.  Push up on the end of the black cartridge, a clicking noise should be heard.

14.  Make sure the orange cap is off of the bottom of the color cartridge.

15.  Place the color cartridge in the bottom of the printer.

16   Slide the color cartridge back until is cannot go back any further.

17.  Push up on the end of the color cartridge, a clicking noise should be heard.

Close the cover.  The PIXMA MG2922 should make some noise for a few moments, and then return to standby.

 

If you continue to have difficulties, please contact our support group using the following link:

http://Canon.us/ContactLI

                   

Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

heinhtetoo
Apprentice
It does´t work......😥😥😥
Announcements
11/22/2022: New firmware available for EOS R3, EOS R7 and EOS R10
11/16/2022: We're thrilled to be ranked among the Best Employers for Veterans in 2022 by Forbes.
10/14/2022: Help ensure your autofocus is properly aligned with a Canon Precision Alignment
09/19/2022: New firmware version 1.0.4.1 is available for EOS C70
08/31/2022: New firmware version 1.1.1 is available for RF 70-200mm L IS USM
08/09/2022: New firmware version 1.2.0 is available for CR-N 300
08/09/2022: New firmware version 1.2.0 is available for CR-N 500
07/28/2022: New firmware version 1.2.1 is available for EOS-R3
07/21/2022: New firmware version 1.6.0 is available for EOS-R5
07/21/2022: New firmware version 1.6.0 is available for EOS-R6
07/21/2022: New firmware version 1.1.0 is available for EOS-R7
07/21/2022: New firmware version 1.1.0 is available for EOS-R10
07/14/2022: New firmware version 1.0.1 is available for CR-X300
07/01/2022: New firmware version 1.3.0 is available for PowerShot PICK
06/10/2022: Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down
06/07/2022: New firmware version 1.3.2 is available for PowerShot G7 X Mark III
06/07/2022: New firmware version 1.0.3 is available for EOS M50 Mark II
05/31/2022: Did someone SAY Badges?
05/26/2022: New firmware version 1.0.5.1 is available for EOS-C500 Mark II
05/26/2022: New firmware version 1.0.3.1 is available for EOS-C300 Mark III
05/10/2022: Keep your Canon gear in optimal condition with a Canon Maintenance Service
05/05/2022: We are excited to announce that we have refreshed the ranking scale within the community!
04/26/2022: New firmware version 1.0.1.1 is available for EOS R5 C
03/23/2022: New firmware version 1.0.3.1 is available for EOS-C70
02/09/2022: Share Your Photos is back!
02/07/2022: New firmware version 1.6.1 is available for EOS-1DX Mark III
01/19/2022: READY FOR ANYTHING EOS-R5 C
01/13/2022: Community Update. We will be retiring the legacy profile avatars on 01/20/2022. Click this link to read more.
01/05/2022: Welcome to CES 2022!