Canon Community Canon Community
 


Reply
New Contributor
Posts: 1
Registered: ‎03-02-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

Took me 2 trys but this worked.  Thank you

New Contributor
Posts: 2
Registered: ‎04-22-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

When you have the power off you can't see any of the buttons light up. Ok button only lights up when power is on. I tried this and it didn't work.

New Contributor
Posts: 2
Registered: ‎04-22-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

I will probably go back to HP printers.

Occasional Contributor
Posts: 13
Registered: ‎09-04-2014

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

Turn off printer

Disconnect from AC

Press OK button on printer 5 times

Reconnect AC

Turn on printer

If this does not work

Try  several more times

If it still does not work

Try again but do not turn on printer until next morning

This has worked for me twice so far.

Also you might try removing the print head and rinsing under hot water until water runs clear before you start the above procedure.

New Contributor
Posts: 2
Registered: ‎05-11-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

Worked for me on first try. Will post again if any further problems.
New Contributor
Posts: 1
Registered: ‎06-04-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

Worked! Thanks!
New Contributor
Posts: 1
Registered: ‎06-14-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

This method worked for me first try! 

Thank you!! 

New Contributor
Posts: 1
Registered: ‎06-21-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

This fix is still good...
Did combo of the 'Hit OK 5 times' and the 'print carriage reset open/close' procedure WITHOUT unplugging power. One or the other or both cleared error. Many thanks!
New Contributor
Posts: 1
Registered: ‎07-12-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

After speaking with a Canon representative that told me I would have to just buy a whole new printer I was willing to try anything! Thank you so much for this solution, Canon should really be willing to try and help more than they were today. I was very disappointed with their customer service.

New Contributor
Posts: 4
Registered: ‎08-23-2016

Re: MX892 getting error B200, any way to fix it? Based on forums this is printing head error.

I had the same experience with Canon help.  Useless.  Tried the methods mentioned here and they didn't help either.  So I've ordered a new printhead.  Lessons learned.  (1) Use the printer at LEAST once a month, even if only for a test page; (2) If leaving for an extended period, do a cleaning BEFORE (and THEN shut it down); (3) DON'T ever let a cartridge run dry.

 

I'm pretty sure I'd have gotten more life out of the printhead if I hadn't violated all three...

 

 

 

powered by Lithium

LIKE US on Facebook FOLLOW US on Twitter WATCH US on YouTube CONNECT WITH US on Linkedin WATCH US on Vimeo FOLLOW US on Instagram SHOP CANON at the Canon Online Store
© Canon U.S.A., Inc.   |    Terms of Use   |    Privacy Statement